Shop

/Shop
  • Part # 8804-C If you are looking for a fuel pump that will feed big power AND is easy to plumb. Our #8804 fuel pump and regulator combo does the trick. This is a carefully selected combination of parts designed to eliminate the high side pressure design fuel systems. These antiquated layouts simply wear the pump out, heat the fuel up and drain your battery. Our #8804 Fuel pump and regulator combo operates on a return setup. This greatly increases pump life and greatly improves fuel pressure accuracy.
    Under High fuel demand or when G-force loads are high, the bypass loads the pump and the pump steps up to give the fuel line those pressure increases needed to keep your carb or nitrous fuel pressure rock solid. BUT, when G-forces or fuel demand is low... like when you slow back down or are driving around, the return style system takes the load off the pump. This layout reduces wear, eliminates heating/boiling of the fuel, simplifies plumbing and reduces battery draw.  
  • Part # P26157
    Are you tired of buying different fuel line kits for different carbs or adding a bowl extension or different metering blocks and then your log won't fit? Well our new adjustable fuel log solves all those issues.  The design fits all the SV1 carburetors, 4150 and even the Dominator style carburetors.
    This is the last fuel log you should ever have to buy.  We thought of everything on this one.  It also includes all the fittings you see here.  The unit uses an o-ring design and extra length sweep to allow it to slide to fit every combination we could think of. This allows for the use of standard or thicker metering blocks, it can be used with or without bowl extensions and is even compatible for carburetors that dont use rear metering blocks (like vacuum secondary carbs).
    The extra large capacity fuel log storage area helps reduce foamed fuel from entering the bowl and it also has provisions for a fuel pressure sensor.
    Its coated for corrosion resistance and is compatible with all street and racing fuels even Q16, Alcohol and E85 fuels.
  • Part # P26100 Air Pans fit between the carburetor and cowl area to keep engine heat away from and direct cool air to the carburetor.  A properly laid out air pan is typically worth 15-25 h.p. and really helps with consistency as underhood temps typically vary exponentially.  Oftentimes as much as 50-80 degrees higher over an outside ambient change of only 5-20 degrees. But building an air pan is tough and time consuming.  This pan really shortens your workload. With high side rails and and a long rear tray, this air pan requires only trimming to fit most applications. Actual Size: 24" Wide X 5" Tall X 28" Long Carb mounting flange is uncut so you can easily locate it in your engine bay.
  • Part # P2000 These Anti Reversion or Shear Plates for 2" bore base plate carburetors (1050 cfm and 1150 cfm Dominator Carburetors are typically 2" bore) are the only way to fight reversion problems.  Reversion problem symptoms are: 1.  Poor throttle response 2.  Poor cylinder to cylinder control of fuel 3.  Difficulty in properly jetting engine 4.  Lazy shift recovery and acceleration These plates simply bolt on between your carburetor and intake manifold and are only 1/2" thick at the deck and the reversion ledges extend down into the intake area a further 1/2". 2" bore Anti Reversion plates: $85.00 each (Gaskets included).
  • Part # P2125 These Anti Reversion or Shear Plates for 2.030 to 2-1/8″ bore base plate carburetors (1250 cfm Dominator Carburetors are typically 2-1/8″ size throttle blades) are the only way to fight reversion problems. Reversion problem symptoms are: 1. Poor throttle response 2. Poor cylinder to cylinder control of fuel 3. Difficulty in properly jetting engine 4. Lazy shift recovery and acceleration These plates simply bolt on between your carburetor and intake manifold and are only 1/2″ thick at the deck and the reversion ledges extend down into the intake area a further 1/2″. 2-1/8″ bore Anti Reversion plates: $85.00 each (Gaskets included).
  • Part # P6002
  • Part # P26156 Fuel Lines, designed for Holley dual feed carburetors, feature braided -8AN line with a -4AN fitting for a fuel pressure gauge. Fuel line is 9-5/16” center to center.
  • Part # P26158 Fuel Lines, designed for Holley Dominator and SV1 series carburetors, feature braided -8AN inlet and -4AN fitting for a fuel pressure gauge.
  • Part # P12-704
  • Part # PG-803 The PG-803 is nothing new. Its a professionally modified Holley regulator that's been used for years in NHRA Pro-Stock competition. Unlike look-alike regulators that make big flow claims yet still utilize the small seat area that froths and foams up the fuel.  We install a 50 percent larger seat area to reduce fuel bowl foam and stabilize the fuel pressure during high flow rates.  You get good clear burnable fuel and more consistent power from run to run. Once again simplistic design is the key to consistency and reliability. The PG-803 has enough flow capability to CLEANLY feed over 1000 horsepower!
  • Part # P7760